J.J. McGlothlin Dist., Inc.
Contact Us
  • Home
  • Our Services
    • Rentals
    • Repair
  • Products
    • DuraSeal >
      • Quick Coat Stain
      • Quick Dry Sealer
      • Dura Finish Liquid Floor Wax
      • Wax & Cleaner
      • Renovator
      • 450 VOC Polyurethane
      • Waterbased Polyurethane
      • Dura Clear Max
      • DuraSeal Paste Wax
      • DuraSeal Hardwood Floor Cleaner
    • Woodwise >
      • Wood Patch
      • Full-Trowel Filler
      • Powdered Wood Filler
      • No Shrink Patch-Quick
      • No Shrink Patch-Quick Extender
      • WOODWISE Pre-Finish Filler
      • EPOXY WOOD PATCH
    • Waterlox
    • Polo Plaz >
      • Supreme Finish
      • Fast Dry Sanding Sealer
      • Supreme Sealer
      • World Class Court and Gym Finish
    • Berger-Seidle >
      • AquaChoice OmniGold
    • American Sanders >
      • Edgers
      • Rotary Sander
      • Floor Crafter
    • Galaxy >
      • Belt Sander
      • Radiator Sander
    • EMack >
      • Ryder Cart
      • Gameline Taping Machine
      • Cadillac Bac Pac
      • Telescopic Pole Kit
      • 3 Phase Voltage Booster
    • We Also Sell...
  • Contact Us

DuraClear Max

Picture
DESCRIPTION
     Non ambering formula. Our most durable two component finish. Formulated for commercial/high traffic areas. Available in Satin, Semi Gloss and Gloss sheens.

SURFACE PREPARATION
  1. NATURAL FLOORS: Sand and prepare floor according to NWFA recommended methods. Finish abrading with a 120 or 150 grit pad or equivalent. Do not use steel wool. Vacuum thoroughly and tack floor with a slightly water dampened cloth to remove all dust. Apply 1 coat of DuraSeal® DuraClear™ Sealer and 2 coats of DuraSeal® DuraClear™ Max Floor Finish.
  2. STAINED FLOORS: Sand and prepare floor according to NWFA recommended methods. Finish abrading with a 100 grit pad or equivalent. Do not use steel wool. Apply DuraSeal® Penetrating Stain or DuraSeal® Quick Coat according to label directions. Apply 2 coats of DuraSeal® DuraClear™ Max Floor Finish over thoroughly dried stain.
  3. PREVIOUSLY FINISHED FLOORS: Note: Do not apply over wax, lacquer, stains or shellac containing wax or stearates. Be certain floor is free from all wax or oily residue. Clean and abrade floor using the DuraSeal® Pre-Treat System. Do not use steel wool. Vacuum thoroughly and tack floor with a slightly water-dampened cloth to remove all dust. Apply 2 coats of DuraSeal® DuraClear™ Max Floor Finish. DuraSeal® DuraClear™ Max Floor Finish will adhere to most stains and finishes after proper preparation. Always prepare a sample or test area to determine compatibility.
DIRECTIONS FOR USE
     SHAKE WELL BEFORE USING. Do not thin. Shake DuraSeal® DuraClear™ Max Floor Finish (Part A) well for 30 seconds prior to adding DuraSeal® DuraClear™ Max Hardener (Part B). One 11 oz. bottle of Hardener will activate one gallon of finish. To activate amounts of finish less than one gallon, use (1) part hardener (Part B) to (10.5) parts finish (Part A). Slowly pour Hardener (Part B) into finish bottle (Part A). Shake mixture for 30-45 seconds then let sit for 5-10 minutes prior to applying. Remove stainless steel screen from the plastic bag and firmly insert the open end of the screen into the large end (bottom) of the spout. The screen should protrude from the bottom of the spout. Insert this entire assembly (screen first) onto the one gallon bottle.

APPLICATION
     Be certain all material is at room temperature. Use a synthetic T-bar applicator to provide the smoothest finish. Best results are achieved when ambient temperatures are between 50°F and 90°F, and humidity below 80%. NOTE: If applying to white oak, two coats of DuraSeal® DuraClear™ Sealer are recommended.

  1. Pour a 5 - 6" wide line of finish along the starting wall, going with the grain of the wood.
  2. Using a clean, dampened applicator, draw the finish toward the opposite wall going with the grain of the wood. Holding the applicator at a "snowplow" angle will allow you to maintain a wet edge at all times.
  3. As you approach the end of the run, turn the applicator toward you and pad out excess material parallel to the wet edge.
  4. Feather out all turns.
  5. Apply DuraSeal® DuraClear™ Max Floor Finish at 500 sq. ft. per gallon to achieve proper film build and prevent lapping and applicator marks.
  6. Allow first coat to dry 2-3 hours before applying next coat. Extended dry time is required with high humidity and low temperature conditions.
  7. Abrade floor lightly with a used DuraSeal® Pre-Treat pad. Vacuum thoroughly and tack floor with a slightly water-dampened cloth to remove all dust. Abrading is not required for additional coats if the finish is applied within 24 hours of the previous coat.
DRY TIME
     Light foot traffic is acceptable after 24 hours. Do not expose the finish to rugs, cleaners, spills or heavy traffic for one week. Dry times are based on conditions of 77°F and 50% relative humidity at the recommended application rates.

CLEAN-UP
     Tools should be cleaned with warm water.

COVERAGE
     Apply at 500 sq. ft. per gal.


Powered by Create your own unique website with customizable templates.